3-867-581-13 (1)
Video Cassette
Recorder
Operating Instructions
PAL NTSC
SLV-SP100R
©1999 by Sony Corporation
Table of contents
Getting Started
4
5
6
8
Step 1: Unpacking
Step 2: Setting up the remote commander
Step 3: Connecting the VCR
Step 4: Tuning your TV to the VCR
Basic Operations
Additional Information
10 Playing a tape
24 Troubleshooting
26 Specifications
27 Index to parts and controls
back cover
Additional Operations
15 Playing/searching at various
Index
speeds
17 Adjusting the picture
19 Editing with another VCR
22 Synchronised recording
Demonstration mode
The demonstration mode will activate when you press STD PICT and
the RESOLUTION CONTROL II down button on the VCR at the same
time.
When demonstration mode starts during playback,
RESOLUTION CONTROL II menu appears and the level of picture
adjustment changes automatically.
When demonstration mode starts during power off and Synchronised
Recording off (page 23), the indicator lights on the VCR flash.
To cancel the demonstration mode
Press STD PICT.
3
Getting Started
Step 1
Unpacking
Check that you have received the following items with the VCR:
• Remote commander
• Aerial cable
• R6 (Size AA) batteries
• Audio/video cable (3-phono to 3-
phono)
4
Getting Started
Step 2
Setting up the remote commander
Inserting the batteries
Insert two R6 (size AA) batteries by
matching the + and – on the batteries to
the diagram inside the battery
compartment.
Insert the negative (–) end first, then push
in and down until the positive (+) end
clicks into position.
Using the remote commander
Remote sensor
You can use this remote
commander to operate the VCR
and a Sony TV. To operate this
VCR, point at the remote
sensor on the VCR. To operate
the TV, point at the remote
sensor on the TV. Buttons in
the shaded area of the remote
commander can be used to
operate your Sony TV. If the
TV does not have the g symbol
near the remote sensor, this
remote commander will not
operate the TV.
TV/VIDEO
; (TV power)
?/1
(on/standby)
PROG(CH) +/–
VOL +/–
To
Press
Turn the TV to standby or active mode
Turn on the TV power
?/1 (on/standby)
; (TV power)
VOL +/–
Increase (+) or decrease (–) the TV volume
Change the TV programme position
PROG(CH) +/–
TV/VIDEO
Select an input source of the TV either from aerial in
or from line in
Notes
• With normal use, the batteries should last about three to six months.
• If you do not use the remote commander for an extended period of time, remove
the batteries to avoid possible damage from battery leakage.
• Do not use a new battery with an old one.
• Do not use different types of batteries.
Getting Started
5
Step 3
Connecting the VCR
Connect the aerial to your VCR and TV as shown below to watch TV
programmes and video pictures on your TV. In addition, if your TV has
audio/video (A/V) input jacks, we recommend you connect the VCR to
your TV using an audio/video cable to get a better picture and sound.
Connecting the aerial
AERIAL
OUT
Aerial cable (supplied)
AERIAL IN
to mains
: Signal flow
1
Disconnect the aerial cable from your TV
and connect it to AERIAL IN on the rear
panel of the VCR.
AERIAL
OUT
IN
AERIAL
OUT
2
3
Connect AERIAL OUT of the VCR and
the aerial input of your TV using the
supplied aerial cable.
IN
Connect the mains lead to the mains.
6
Getting Started
Additional connections
To a TV that has audio/video
input jacks
This VCR
TV
AUDIO VIDEO
LINE 1 IN
This additional connection
improves picture and sound quality.
Connect the TV as shown on the
right.
IN
LINE 1 OUT
VIDEO
AUDIO
Audio/video cable (supplied)
If you want to use the Trinitron TV
Synchro Play function (see page 14),
this connection is necessary. (If
your TV has two or more inputs,
connect the audio/video cable to
the VIDEO IN 1 jacks.)
To a stereo system
Stereo system
This VCR
You can improve sound quality by
connecting a stereo system as
shown on the right.
AUDIO VIDEO
LINE 1 IN
AUX IN
LINE 1 OUT
Audio cable (not supplied)
Note
• To listen to playback sounds in stereo, you must use either of the connections above.
Getting Started
7
Step 4
Tuning your TV to the VCR
If you have connected your VCR to the TV using the audio/video cable, skip
this step.
?/1 ON/STANDBY
H PLAY
ON/STANDBY
1
2
Press ?/1 ON/STANDBY to turn on the VCR.
Turn on your TV and select a programme position for the video
picture.
This channel will now be referred to as the video channel.
Some TV has the programme position, such as 0, that is reserved for
a VCR. In this case, select that programme position for the video
picture. Refer to the instruction manual of your TV for details.
3
Tune the TV until the video picture on
the right is clearly displayed on the TV
screen.
SONY
VIDEO CASSETTE PLAYER
Refer to your TV manual for tuning
instructions.
You have now tuned your TV to the
VCR. From now on, whenever you
want to play a tape, set the TV to the
video channel.
If the playback picture does not appear clearly, see “To obtain a clear
playback picture” on page 9.
8
Getting Started
To obtain a clear playback picture
If the playback picture does not
appear clearly in step 3 on page 8,
turn the RF CHANNEL screw on
the rear panel of the VCR with a
screwdriver to a position where the
TV clearly displays the playback
picture.
RF CHANNEL
To select the TV system
For your TV to receive the correct
signal from your VCR you must set
the TV SYSTEM switch on the rear
panel of the VCR to either G (for
system B/G) or K (for system D/K).
If this switch is set to the wrong
position, the sound will be
TV SYSTEM
G
distorted.
K
Getting Started
9
Basic Operations
Pla yin g a t a p e
Z EJECT
DISPLAY
H PLAY
A EJECT
m 3 REW M # FF
NTSC PB
X PAUSE
M FF
H PLAY
x STOP
m REW
x STOP
COLOR
X PAUSE
SYSTEM
1
2
Turn on your TV and set it to the video channel.
Insert a tape.
The VCR turns on and starts playing
automatically if you insert a tape with
its safety tab removed.
PLAY
3
Press H PLAY (if playback did not start in step 2).
When the tape reaches the end, it will rewind automatically.
10 Basic Operations
Additional tasks
To
Press
Stop play
Pause play
x STOP
X PAUSE
Resume play after pause X PAUSE or H PLAY
Fast-forward the tape
Rewind the tape
Eject the tape
M FF (M # FF on the VCR) during stop
m REW (m 3 REW on the VCR) during stop
Z EJECT
To set the colour system
If streaks appear during playback, set COLOR SYSTEM on the VCR to
conform to the system that the tape was recorded in. (Normally set the
switch to AUTO.)
If your tape w as recorded in
Set COLOR SYSTEM to
PAL/ MESECAM
PAL
NTSC
NTSC
MESECAM
PAL/ MESECAM
To play an NTSC-recorded tape
Set NTSC PB on the VCR according to the colour system of your TV.
If your TV is
PAL
Set NTSC PB to
ON PAL TV
NTSC 4.43
NTSC 4.43
NTSC 3.58
NTSC 3.58
continued
Basic Operations
11
Pla yin g a t a p e (co n t in u e d )
To view the tape status on the screen
Press DISPLAY.
The following information appears on the TV screen.
STEREO
Audio monitor mode*
Remaining tape length
Time counter
–
0
S
E
:
:
SP
00 22
Tape speed*
* Appears for a few seconds when the DISPLAY button is pressed and when the
mode is changed.
To turn the display off, press DISPLAY again.
Notes
•
You can eject a tape even when the power is off. When you press Z EJECT, the VCR
turns on automatically. After ejecting the tape, the VCR turns off again.
•
When the pause mode lasts for more than approximately five minutes, the VCR will
automatically enter the playback mode.
•
•
•
•
You can play back tapes recorded in the SP mode only.
The counter resets to “0:00:00” whenever a tape is inserted.
The counter stops counting when it comes to a portion with no recording.
If a tape has portions recorded in both PAL and NTSC systems, the time counter
reading will not be correct. This is due to the difference between the counting cycles
of the two colour systems.
•
Depending on your TV, the following may occur while playing an NTSC-recorded
tape:
– the picture is black and white,
– the picture shakes,
– no picture appears on the TV screen,
– black streaks appear horizontally on the TV screen, and
– the colour density increases or decreases.
12 Basic Operations
Se le ct in g t h e so u n d
d u rin g p la yb a ck
AUDIO
MONITOR
Press AUDIO MONITOR to select
the sound you want. Each press
of the button changes the
indicator in the display window.
When you play a tape recorded in
stereo or with a bilingual sound
track, the Hi-Fi indicator in the
display window lights up.
To listen to a
Press AUDIO MONITOR until the
display w indow indicator show s
Stereo tape’s
Bilingual tape’s
Main and sub sounds
Main sound
Stereo sound
Left channel
Right channel
L/ R
L
Sub sound
R
1
Standard sound*
Standard sound*2
No indication
*1 Usually the mixed sound of left and right channels (monaural)
*2 Usually the main sound (monaural)
How sound is recorded on a video tape
The VCR records sound onto two separate tracks. Hi-fi audio is recorded
onto the main track along with the picture. Monaural sound is recorded
onto the normal audio track along the edge of the tape.
Stereo
Usually mixed
Bilingual
Usually main
left/right channels
sound
Normal audio track
(monaural)
Hi-fi audio track
(main track)
Stereo sound
(left/right channels)
Main (left channel)
Sub (right channel)
Notes
•
•
To listen to playback sounds in stereo, you must use the AUDIO OUT connections.
When you play back a tape recorded in monaural, the sound is heard in monaural
regardless of the AUDIO MONITOR setting.
•
You cannot select the sound to listen to while recording.
continued
Basic Operations
13
Pla yin g a t a p e (co n t in u e d )
Tu rn in g o n t h e VCR a n d TV, a n d st a rt in g p la yb a ck
a u t o m a t ica lly (Trin it ro n TV Syn ch ro Pla y)
You can only use this function if your TV is made by Sony (Trinitron TV).
How to connect to use this function
Connect the VCR and TV with the audio/ video cable (see “To a TV that has
audio/ video input jacks” on page 7.) Be sure to connect the audio/ video
cable to the VIDEO IN 1 jacks on the TV if the TV has two inputs or more.
The TV must be placed where it will respond to the remote commander
while you are pointing it at the VCR.
Operation
Make sure that the TV’s power is in standby mode.
Press TRINITRON TV SYNCHRO PLAY and hold the remote commander in
place for about two seconds.
The VCR and TV turn on, and the TV is set to the video channel. If there is a
tape in the VCR, playback starts automatically.
Notes
•
If the Trinitron TV Synchro Play function does not work properly:
- Wait a few moments, and press the button again.
- Replace both of the batteries in the remote commander with new ones, and press
the button again.
Note that this function may not operate some Sony TVs because of the remote
commander’s signal limitations.
•
Do not press TRINITRON TV SYNCHRO PLAY while playing back a video tape. If
you do so, the TV’s input source will momentarily switch to the TV’s tuner.
14 Basic Operations
Additional Operations
Pla yin g /se a rch in g
a t va rio u s sp e e d s
3/#
SEARCH
H PLAY
m 3 REW
M # FF
y SLOW
M FF
H PLAY
m REW
Playback options
Operation
View the picture during fast- During fast-forward, hold M FF (M # FF on the VCR) down.
forward or rewind
During rewind, hold m REW (m 3 REW on the VCR) down.
Play at high speed
•
•
During playback or pause, press # SEARCH or 3 SEARCH.
During playback or pause, hold down M FF (M # FF on
the VCR) or m REW (m 3 REW on the VCR). When you
release the button, normal playback resumes.
Play in slow motion
During playback or pause, press y SLOW.
During stop, press H PLAY on the VCR while holding down
Rewind and start play
m 3 REW on the VCR.
continued
Additional Operations 15
Pla yin g /se a rch in g a t va rio u s sp e e d s (co n t in u e d )
To resume normal playback
Press H PLAY.
Tips
•
You can adjust the tracking just by pressing V/ v NORMAL/ SLOW/ STILL ADJUST
while playing a tape.
•
Adjust the picture using V/ v NORMAL/ SLOW/ STILL ADJUST if:
– streaks appear while playing in slow motion
– the picture shakes while pausing
Notes
•
Streaks or snow cannot be eliminated completely in the various playback
operations, especially in the slow motion mode.
•
•
The sound is muted during these operations.
On screen symbols may shake while playing or searching at various speeds.
16 Additional Operations
Ad ju st in g t h e
p ict u re
AUTO/MANU
Although the VCR automatically adjusts
the picture when playing a tape,
distortions or noise may occur if the tape
was recorded in poor condition. If so,
manually adjust the resolution, colour
and tracking.
V/v NORMAL/
SLOW/STILL ADJUST
M/m/</,
Resolution
Control II
STANDARD
PICTURE
RESOLUTION CONTROL II
buttons
STD PICT
Ad ju st in g t h e re so lu t io n a n d co lo u r
RESOLUTION CONTROL II
1
While playing a tape, press M/ m/ </ ,
RESOLUTION CONTROL II (up/ down/ left/
right button on the VCR) to display the
RESOLUTION CONTROL II menu.
•
•
•
•
•
•
•
•
•
•
• C
O
•
• + • • L
O
•
•
•
•
•
•
•
• R
The RESOLUTION CONTROL II buttons light
up.
RESOLUTION
2
3
Press </ , RESOLUTION CONTROL II (left/ right button on the
VCR) to get a clearer picture.
Press M/ m RESOLUTION CONTROL II (up/ down button on the VCR)
to get the best picture colour.
Wait for several seconds until the RESOLUTION CONTROL II menu
disappears.
To resume the automatic adjustment
Press STANDARD PICTURE on the remote commander (STD PICT on the
VCR) so that the RESOLUTION CONTROL II buttons turn off.
Ad ju st in g t h e t ra ckin g
Press V/ v TRACKING NORMAL/ SLOW/ STILL ADJUST to obtain the best
possible picture. The distortion should disappear as you press one of the two
buttons. If you cannot get a clear picture with manual adjustment, press
TRACKING AUTO/ MANU to return to automatic adjustment.
continued
Additional Operations 17
Ad ju st in g t h e p ict u re (co n t in u e d )
Ab o u t Ad a p t ive Pict u re Co n t ro l (APC)
Adaptive Picture Control (APC) automatically improves recording and
playback quality by adjusting the VCR to the condition of the video heads
and tape.
APC playback
The APC function automatically works on all types of tapes, including rental
tapes and tapes that were not recorded with APC.
APC recording
Whenever you insert a tape and first start recording, the VCR adjusts to the
tape using the APC function. This adjustment is retained until the tape is
ejected.
Tip
•
Adjust the picture using V/ v NORMAL/ SLOW/ STILL ADJUST if:
– streaks appear while playing in slow motion
– the picture shakes while pausing
Notes
•
The auto tracking function works automatically when you play back a tape just
after inserting it.
•
There is a delay of a few seconds before the VCR actually starts recording while the
VCR analyses the tape. To avoid the delay, first set the VCR to recording pause and
press z REC to have the VCR analyse the tape. After ten seconds, press X PAUSE
to start recording immediately. If you press X PAUSE before ten seconds, the APC
function is cancelled.
•
•
•
While playing a MESECAM recorded tape, you cannot adjust the colour using the
RESOLUTION CONTROL II function.
Sufficient picture quality may not be obtained when playing back tapes recorded on
another VCR or tapes in poor condition.
When a tape recorded with the copyguard system is played back, intermittent
distortion may appear in the upper portion of the picture. However, this is not a
malfunction of the VCR.
18 Additional Operations
Ed it in g w it h a n o t h e r VCR
Ho w t o co n n e ct t o re co rd o n t h is VCR
TV
This VCR (Recorder)
LINE 1 IN
Other VCR (Player)
LINE OUT
VMC-810HG audio/video cable (not supplied)
: Signal flow
Tip
•
If the other VCR is a monaural type and connected to the LINE 1 IN jacks on this
VCR, the sound is recorded only on the channel whose jack is connected to the
audio plug. To record on both right and left channels, connect the audio plugs to
AUDIO R/ L jacks using the VMC-910HG (3-phono to 2-phono) audio/ video cable
(not supplied).
Notes
•
•
Make sure you connect the plugs to jacks of the same colour.
If you connected this unit to both the LINE IN and LINE OUT jacks of the other
VCR, select the input correctly to prevent a humming noise.
•
Make sure you set the CONNECT LINE-1 switch to OTHERS.
continued
Additional Operations 19
Ed it in g w it h a n o t h e r VCR (co n t in u e d )
Op e ra t io n (w h e n
re co rd in g o n t h is VCR)
X PAUSE z REC
You can make a copy of a tape using
this VCR for recording or playback.
The VCR cannot record TV
programmes directly since it does
not have a TV tuner.
Before you start editing
• Turn on your TV and set it to the
video channel.
1
2
Insert a source tape with its safety tab removed into the other
(playback) VCR. Search for the point to start playback and set it to
playback pause.
Insert a tape with its safety tab in place into this (recording) VCR.
Search for the point to start recording and press X PAUSE.
3
4
Press z REC on this VCR to set it to recording pause.
To start editing, press the X PAUSE buttons on both VCRs at the same
time.
To stop editing
Press the x STOP buttons on both VCRs.
To check the remaining tape length
Press DISPLAY.
The white bar indicates the approximate length of the tape recording.
Remaining tape length
Time counter
–
0
S
E
:
:
00 22
To turn the display off, press DISPLAY again.
20 Additional Operations
To save a recording
To prevent accidental erasure, break off the safety
tab as illustrated. To record on a tape again, cover
the tab hole with adhesive tape.
Safety tab
Tips
•
•
To edit more precisely, press the X PAUSE buttons on the VCRs to release pause.
To cut out unwanted scenes while editing, press X PAUSE on this VCR when an
unwanted scene begins. When that scene ends, press X PAUSE again to resume
recording.
Note
You can record tapes only in SP mode.
•
Additional Operations 21
Syn ch ro n ise d re co rd in g
The Synchronised Recording feature enables you to record from the
connected equipment such as a satellite tuner, a cable TV decoder or a TV
that has a timer function. Once you set the timer on the other equipment, the
VCR will start recording the programme synchronised with the timer.
Ho w t o co n n e ct t o u se t h is fu n ct io n
Connect the other equipment to the LINE 1 IN jacks of this VCR.
This VCR (Recorder)
TV, Satellite tuner, etc.
CONNECT
LINE-1
TV
OTHERS
LINE 1 IN
LINE OUT
VMC-810HG audio/video cable (not supplied)
: Signal flow
Setting the CONNECT LINE-1 sw itch
When you connect the other equipment to the LINE 1 IN jacks, set the
CONNECT LINE-1 switch on the rear of the VCR following the table below
to allow better signal transmission to your TV.
If the VCR is connected to
TV
Set the CONNECT LINE-1 sw itch to
TV
Satellite, cable TV decoder, etc.
OTHERS
22 Additional Operations
To p re p a re t h e Syn ch ro n ise d re co rd in g
SYNCHRO REC
1
2
3
Set the timer on the equipment to the time of the programme you want
to record, then turn the equipment off.
Insert a tape with its safety tab in place. Make sure the tape is longer
than the total recording time.
Hold SYNCHRO REC down for more than two seconds.
The SYNCHRO REC button lights up and the VCR stands by for
recording.
The VCR automatically turns on and starts recording when it receives
audio/ video signals from the connected equipment.
To cancel the Synchronised recording
Press SYNCHRO REC so that the button’s light turns off.
To stop recording
Press x STOP while recording.
The VCR automatically stops recording when the tape reaches the end or
when the other equipment stops transmitting the audio/ video signals.
Notes
•
•
•
•
Some TVs or other equipment automatically turn off in a certain time if you do not
operate it after it turns on with the timer. In this case the Synchronised Recording
also stops automatically.
The Synchronised Recording starts and stops according to the signals from the
connected equipment. Refer also to the instruction manual of the connected
equipment for its timer function.
Some equipment keeps transmitting signals even though the power is off. In this
case, the Synchronised Recording feature does not work because the VCR will not
be able to know when to start recording.
You can record tapes only in SP mode.
Additional Operations 23
Additional Information
Tro u b le sh o o t in g
If you have any questions or problems not covered below, please consult your
nearest Sony service facility.
Symptom
Remedy
The ?/1 ON/STANDBY switch • Connect the mains lead securely.
does not function.
The power is turned on but the
VCR does not operate.
• Moisture condensation has occured. Turn the power
off, unplug the mains lead and leave the VCR to dry
for over an hour.
The VCR enters standby mode
or turns off automatically.
• The auto safety system is triggered to protect your tape
and the VCR’s mechanism when there is something
wrong with the tape or when the mechanism is
overloaded. Press ?/1 ON/STANDBY to restart the
VCR. If the VCR does not work after pressing ?/1
ON/STANDBY again, disconnect the mains lead from
the mains. Wait for at least 15 seconds. Then reconnect
the mains, and press ?/1 ON/STANDBY again. If the
VCR still does not work, please consult your nearest
Sony service facility.
The playback picture does not
appear on the TV screen.
• Make sure the TV is set to the video channel. If you are
using a monitor, set it to video input.
The picture is not clear.
• Adjust the tracking with the V/v NORMAL/SLOW/
STILL ADJUST buttons.
• Make sure the COLOR SYSTEM switch is set to the
position corresponding to the colour system which the
tape was recorded with.
• The video heads are dirty (see next page). Clean the
video heads using the Sony T-25CLD, T-25CLW or E-
25CLDR video head cleaning cassette. If these cleaning
cassettes are not available in your area, have the heads
cleaned at your nearest Sony service facility (a
standard service charge will be required). Do not use a
commercially available liquid type cleaning cassette, as
it may damage the video heads.
• The video heads may have to be replaced. Consult
your local Sony service facility for more information.
The picture rolls vertically
during picture search.
• Adjust the vertical hold control on the TV or monitor.
The picture has no sound.
• The tape is defective.
• If you made A/V connections, check the audio cable
connection.
24 Additional Information
Symptom
Remedy
The tape starts playing as soon
as it is inserted.
• The safety tab has been removed. To record on this
tape, cover the tab hole.
The tape is ejected when you
press z REC.
• Check that the safety tab has not been removed.
Nothing happens when you
press z REC.
• Make sure the tape is not at its end.
A tape cannot be inserted.
• Check that a tape is not already in the tape
compartment.
The remote commander does
not function.
• Make sure you are pointing the remote commander at
the remote sensor on the VCR.
• Replace all the batteries in the remote commander with
new ones if they are weak.
The VCR needs to be cleaned.
• Clean the cabinet, panel, and controls with a dry soft
cloth, or a soft cloth slightly moistened with a mild
detergent solution. Do not use any type of solvent,
such as alcohol or benzine.
The indicator lights on the VCR • The demonstration mode has been turned on. Cancel
are flashing.
the demonstration mode by pressing STD PICT.
The RESOLUTION CONTROL II
menu appears automatically.
Auto head cleaner
The VCR incorporates an auto head cleaner which cleans the video
heads when a tape is loaded or unloaded. When the heads are not
sufficiently clean, even after a tape has been loaded/unloaded several
times, use a video head cleaning cassette.
Symptoms caused by contaminated video heads
• Normal picture
• Rough picture
• Unclear picture
• No picture (or
black & w hite
screen appears)
initial
terminal
contamination
Additional Information 25
Sp e cifica t io n s
Syst e m
Su p p lie d a cce sso rie s
Colour system
Remote commander (1)
PAL, MESECAM, NTSC 3.58, NTSC 4.43
RF output signal
R6 (Size AA) batteries (2)
Aerial cable (1)
UHF channels 30 to 39
(B/G, D/K)
Audio/video cable (3-phono to 3-phono) (1)
Aerial out
Design and specifications are subject to change
without notice.
75-ohm asymmetrical aerial socket
In p u t s a n d o u t p u t s
LINE 1 IN
VIDEO IN, phono jack (1)
Input signal: 1 Vp-p, 75 ohms,
unbalanced, sync negative
AUDIO IN, phono jack (2)
Input level: 327 mVrms
Input impedance: more than 47 kilohms
LINE 1 OUT
VIDEO OUT, phono jack (1)
Output signal: 1 Vp-p, 75 ohms,
unbalanced, sync negative
AUDIO OUT, phono jack (2)
Standard output: 327 mVrms
Load impedance: 47 kilohms
Output impedance: less than 10 kilohms
Ge n e ra l
Power requirements
110 – 240 V AC, 50/60 Hz
Power consumption
12 W
Operating temperature
5°C to 40°C
Storage temperature
–20°C to 60°C
Dimensions
Approx. 355 × 96 × 293 mm (w/h/d)
including projecting parts and controls
Mass
Approx. 3.8 kg
26 Additional Information
In d e x t o p a rt s a n d co n t ro ls
Refer to the pages indicated in parentheses ( ) for details.
Fro n t p a n e l
1 1/u ON/STANDBY switch/
q; NTSC PB switch (11)
indicator (8)
qa COLOR SYSTEM switch (11)
qs Remote sensor (5)
2 Tape operation indicator
3 HiFi/L/R indicators (13)
4 p STOP button (11)
5 Tape compartment
qd r REC (record) button (20)
qf )# FF (fast-forward) button (11,
15)
6 P PAUSE button (11)
7 § EJECT button (11)
qg · PLAY button (10)
qh 03 REW (rewind) button (11, 15)
qj SYNCHRO REC (record) button (23)
8 RESOLUTION CONTROL II
buttons (17)
9 STD PICT (standard picture) button
(17)
continued
Additional Information 27
In d e x t o p a rt s a n d co n t ro ls (co n t in u e d )
Re a r p a n e l
1 Mains lead (6)
5 CONNECT LINE-1 switch (22)
2 RF (Radio Frequency) CHANNEL
6 LINE 1 OUT AUDIO R/L/VIDEO
screw (9)
jacks (7)
3 AERIAL OUT connector (6)
7 AERIAL IN connector (6)
4 LINE 1 IN AUDIO R/L/VIDEO
8 TV SYSTEM switch (9)
jacks (19)
28 Additional Information
Re m o t e co m m a n d e r
1 Z EJECT button (11)
2 TV control buttons (Only for TV) (5)
TV/VIDEO
a (TV power)
?/1 (on/standby)
VOL (volume) +/–
PROG (CH) +/–
3 TV/VIDEO button (This button
doesn’t work with this unit.)
4 DISPLAY button (12, 20)
5 TRACKING buttons
AUTO/MANU (17)
V/v NORMAL/SLOW/STILL
ADJUST (17)
6 z REC (record) button (20)
7 AUDIO MONITOR button (13)
8 X PAUSE button (11)
9 m REW (rewind) button (11, 15)
q; H PLAY button (10)
qa x STOP button (11)
qs TRINITRON TV SYNCHRO PLAY
button (14)
qd ?/1 (on/standby) switch (8)
qf M/m/</, Resolution Control II
buttons (17)
qg STANDARD PICTURE button (17)
qh 3/# SEARCH buttons (15)
qj y SLOW button (15)
qk M FF (fast-forward) button (11, 15)
Additional Information 29
Index
A, B
Accessories supplied
Adjusting picture
colour 17
D
R
4
Demonstration mode 3, 25
Dubbing. See Editing
Recording 20
Synchronised 22
Remote commander
5
resolution 17
tracking 17
E, F, G
Editing 19
Resolution adjustment 17
Resolution Control II 17
RF (Radio Frequency)
Aerial hookup
6
CHANNEL screw
9
APC (Adaptive Picture
Control) 18
Audio track 13
Auto head cleaner 25
AV (audio/video)
H, I, J, K, L
Hi-fi audio track 13
S
Safety tab 21
M
Searching at various
speeds 15
SP mode 12, 21
Monitoring
during playback 13
connection
7
C
Synchronised recording 22
N, O
Cleaning the video
heads 24
Normal audio track 13
NTSC-recorded tapes 11
T, U, V, W, X, Y, Z
Tracking adjustment 17
Trinitron TV Synchro
Play 14
Tuning your TV to the
Colour adjustment 17
Colour system
P, Q
compatible colour
Picture adjustment 17
Playback 10
systems
2
setting 11
VCR
8
at various speeds 15
slow motion 15
Connecting
TV system
9
the VCR and your TV
to a TV with audio/
6
video jacks
7
Sony Corporation Printed in Malaysia
|
Shure Headphones SRH550DJ User Manual
Silex technology Network Card SX 1000U User Manual
Sony Clock Radio ICF CD837L User Manual
Sony Computer Drive MSH 128 User Manual
Sony Laptop VPCJ2 Series User Manual
Sony MP3 Player WM EX2000 User Manual
Sony Satellite TV System VCA 130 User Manual
Sterling Thermostat 6016 M User Manual
Strong Pools and Spas Hot Tub Liberty User Manual
Sunbeam Electric Steamer FOOD STEAMER User Manual